BAER HSSG Hand Tap Set (2pcs.) conical UNEF 9/16 x 24
BAER HSSG Hand Tap Set (2pcs.) conical UNEF 9/16 x 24
The hand tap set in conical design consists of two taps and allows you to cut a finished thread with significantly reduced risk of breakage. The advantage of two-piece hand tap sets is that the respective parts of a set share the cutting power. In contrast to normal hand taps sets, you can cut a complete thread with each individual screw tap in the conical version. In addition, the taper tap (No. 1) does not have a ring marking. The taps all have a fully formed thread profile, but the gate lengths differ: The taper tap (No. 1) in form A has a gate length with 6 - 8 threads and the finishing tap (No. 3) with form C has a gate of 2 - 3 threads and can therefore cut a deep usable thread and thus also enables blind holes to be cut almost to the bottom. The division of labour between the two screw tap makes it easier to cut a straight and clean thread by hand.
Compared to the machine tap, the hand tap has a short shank. This allows you to cut internal thread by hand without jamming and can be operated with tap wrenches, tool ratchets or other holding tools with square drive.
The thread can be cut in a pre-drilled core hole.
Due to the short gate of the finish tap, the hand tap set is reliable and universally applicable for through holes and blind holes.
As a rule, two-piece hand taps- sets are used for fine threads, as the thread profile area is smaller than for coarse threads and the force effects on the taps are smaller.
Dimensions
Diameter |
9/16 |
---|---|
Nominal diameter in inches |
0,563 |
Nominal diameter in mm |
14,288 |
Pitch |
24 |
Pitch in mm |
1,058 |
Dimension |
UNEF 9/16 x 24 |
Characteristics
Product group |
Screw taps |
---|---|
Product type |
Hand tap sets |
Thread standard |
UNEF: American Extra Fine Unified National thread according to ANSI B1.1 |
Tolerance |
2B |
Direction |
Right |
Standard |
ISO 547 |
Tensile strength at room temperature |
up to 900 N/mm² | 27.1 HRC |
Material |
HSSG bright |
13.3 mm
Through hole and blind hole up to 2 x D
Form C straight fluted
2-3 threads
Rarely occurs. Chips remain in flutes.
External cooling and lubrication
HSSG bright
up to 900 N/mm² | 27.1 HRC
2B
Applications
- Materials with good machinability up to 900 N/mm²
- Unalloyed and low-alloy steels
Technical drawing
D1 |
UNEF 9/16 x 24 |
---|---|
D2 |
11,2 mm |
L1 |
95 mm |
L2 |
30 mm |
Diameter |
9/16 |
Square |
9 mm |
Application – Sample materials for taps
Unalloyed construction steels | |
---|---|
1.0035 | S185 (St33) |
1.0036 | S235JRH |
1.0038 | RSt37-2 |
1.0039 | S235JRG1+CR |
1.0044 | St44-2 |
1.0060 | E335 (St60-2) |
1.0116 | St37-3 |
1.0570 | St 52-3 |
Alloyed construction steels | |
---|---|
1.5415 | 15Mo3 |
1.5423 | 16Mo5 |
1.5622 | 14Ni6 |
1.7335 | 13CrMo44 |
1.7337 | 16CrMo44 |
1.7715 | 14MoV63 |
Free-cutting steels | |
---|---|
1.0711 | 9S20 |
1.0715 | 9SMn28 |
1.0718 | 11SMnPb30 |
1.0721 | 10S20 |
1.0723 | 15S20 |
1.0726 | 35S20 |
1.0737 | 9SMnPb36 |
1.0758 | 60SPb20 |
Case-hardening steels | |
---|---|
1.0401 | (C15) |
1.7016 | 17CR3 |
1.7131 | 16MnCr5 |
1.5919 | 15CrNi6 |
Quenched and tempered steels unalloyed | |
---|---|
1.0402 | C 22 |
1.1151 | C22E (Ck22) |
1.0503 | C 45 |
1.1191 | C45E (Ck45) |
Cast steel | |
---|---|
1.0420 | GS-38 |
1.5419 | GS-22 Mo 4 |
1.6750 | GS-20 NiCrMo3 7 |
1.7357 | GS-17 CrMo 5 5 |
Malleable cast iron | |
---|---|
0.8145 | EN-GJMB 450-6 |
0.8170 | EN-GJMB 700-2 |
0.8045 | EN-GJMW-450-7 |
0.8055 | EN-GJMW-550-4 |
Pure copper low-alloyed | |
---|---|
2.0240 | CuZn15 |
2.0265 | CuZn30 |
Brass short-chipping | |
---|---|
2.0401 | CuZn39Pb3 |
Brass long-chipping | |
---|---|
2.0321 | CuZn37 |
2.0335 | CuZn36 |
2.0360 | CuZn40 |
Aluminum cast Si > 5-12 % | |
---|---|
3.2161 | G-AlSi8Cu3 |
3.2163 | G-AlSi9Cu3 |
3.2381 | G-AlSi10Mg |
3.2583 | G-AlSi12(Cu) |
Lamellar graphite cast iron | |
---|---|
0.6010 | EN-GJL 100 (GG-10) |
0.6020 | EN-GJL 200 (GG -20) |
0.6025 | EN-GJL 250 (GG-25) |
0.6030 | EN-GJL 300 (GG -30) |
Copper-tin alloy (bronze) short-chipping | |
---|---|
2.1090.01 | G-CuSn7ZnPb |
2.1086.01 | G-CuSn10Zn |
2.1097 | G-CuSn5ZnPb |
Pure copper, low-alloyed copper | |
---|---|
2.0240 | CuZn15 |
2.0265 | CuZn30 |
Further information
- UNEF - Unified National Extra Fine Thread Series ANSI B1.1 American extra fine thread
- Designations, geometries and definitions on taps
- Thread tolerances of the internal thread
- Internal thread and core hole dimensions
- Tap Chamfer forms
- Comparison inch-mm
- Surface treatments on tapping tools
- Information about tapping
- Material table