BAER HSSE Hand Tap Set (2pcs.) G (BSP) 1/8 x 28
BAER HSSE Hand Tap Set (2pcs.) G (BSP) 1/8 x 28
The hand tap set consists of two taps and allows you to cut a finished thread with significantly reduced risk of breakage. The advantage of two-piece hand taps is that the respective parts of a set share the cutting power: The taper tap (No. 1) (marked with a ring) removes 65 per cent of the thread profile and the and brings the thread into shape. The finishing tap (No. 3) has no ring marking and cuts the remaining thread profile to produce the 100% full and usable thread. The division of labour between the two screw tap makes it easier to cut a straight and clean thread by hand.
Compared to the machine tap, the hand tap has a short shank. This allows you to cut internal thread by hand without jamming and can be operated with tap wrenches, tool ratchets or other holding tools with square drive.
The thread can be cut in a pre-drilled core hole.
Due to the short chamfer of the finish tap, the hand tap set can be used reliably and universally for through holes and blind holes.
As a rule, two-piece hand taps- sets are used for fine threads with a smaller pitch than with coarse thread, as the thread profile surface is smaller than with coarse threads and the force effects on the taps are smaller.
Dimensions
Diameter |
1/8 |
---|---|
Nominal diameter in inches |
0,383 |
Nominal diameter in mm |
9,73 |
Pitch |
28 |
Pitch in mm |
0,907 |
Dimension |
G (BSP) 1/8 x 28 |
Characteristics
Product group |
Screw taps |
---|---|
Product type |
Hand tap sets |
Thread standard |
G (BSP): British Standard Pipe Thread according to DIN ISO 228 - Cylindrical pipe thread |
Tolerance |
medium |
Direction |
Right |
Standard |
DIN 5157 |
Tensile strength at room temperature |
up to 1200 N/mm² | 38 HRC |
Material |
HSSE bright |
8.8 mm
Through hole and blind hole up to 2 x D
Form C straight fluted
2-3 threads
Rarely occurs. Chips remain in flutes.
External cooling and lubrication
HSSE bright
up to 1200 N/mm² | 38 HRC
medium
Applications
- Difficult to machine materials
- Steels up to 1200 N/mm²
Examples of applications
- Inch thread or Whitworth thread in the sanitary sector
- G-pipe pipe thread
- Fittings, connectors, nipples, threaded fittings for water pipes, sanitary threads, water threads
- Double nipples and double pipe nipples
- Angle connection
- Pipe threaded connections
Technical drawing
D1 |
G (BSP) 1/8 x 28 |
---|---|
D2 |
7 mm |
L1 |
63 mm |
L2 |
20 mm |
Diameter |
1/8 |
Square |
5,5 mm |
Application – Sample materials
General construction steels | |
---|---|
1.0035 | S 185 (St 33) |
1.0036 | S 235 JRH |
1.0039 | S 235JRG1+CR |
1.0060 | E 335 (St 60-2) |
Free-cutting steels | |
---|---|
1.0718 | 11SMnPb30 |
1.0721 | 10S20 |
1.0726 | 35S20 |
1.0728 | 60S20 |
Case-hardening steels | |
---|---|
1.0401 | (C15) |
1.7016 | 17 CR3 |
1.7131 | 16MnCr5 |
1.5919 | 15CrNi6 |
Quenched and tempered steels unalloyed | |
---|---|
1.0402 | C 22 |
1.1151 | C22E (Ck 22) |
1.0503 | C 45 |
1.1191 | C45E (Ck 45) |
Cast steel | |
---|---|
1.5681 | GS-10 Ni 19 |
1.6760 | GS-22 NiMoCr 5 6 |
Quenched and tempered steels alloyed | |
---|---|
1.1133 | 20Mn5 |
1.5710 | 36NiCr6 |
Further information
- G (BSP) - British Standard Pipe DIN ISO 228 - Cylindrical pipe thread
- Whitworth Pipe Thread
- Designations, geometries and definitions on taps
- Thread tolerances of the internal thread
- Internal thread and core hole dimensions
- Tap Chamfer forms
- Comparison inch-mm
- Surface treatments on tapping tools
- Information about tapping
- Material table